裝載機上的破碎器使用方法
[ 發布日期:2023-01-07 15:10:28 ] 來源:永保機械 瀏覽:357次
選用裝載機液壓破碎器的原則是根據裝載機的作業穩定性、工作裝置液壓回路的工作壓力機功率消耗來選擇最合適的液壓破碎器。
1、裝載機使用前仔細閱讀液壓破碎器的操作手冊,防止損壞液壓破碎器,并有效地操作它們,操作前檢查螺栓和連接頭是否松動,以及液壓管路是否有泄漏現象。
Read Shandong loader operation manual carefully before using the hydraulic breaker to prevent damage to the hydraulic breaker and effectively operate them, preflight check for loose bolts and connectors, as well as hydraulic lines for leaks.
2、不要用液壓破碎器在堅硬的巖石上啄洞,不得在液壓缸的活塞桿全伸或全縮狀況下操作破碎器。
Do not peck at the hard rock hole with a hydraulic breaker, may not fully extended or full reduction condition in the hydraulic cylinder piston rod operating breaker.
3、當液壓軟管出現激烈振動時應停止破碎器的操作,并檢查蓄能器的壓力,防止裝載機的動臂與破碎器的鉆頭之間出現干涉現象,除鉆頭外,不要把破碎器浸入水中。
Intense vibration occurs when the hydraulic hose should stop breaking the operation and check the accumulator pressure, prevent interference occurs between the boom and the breaker drill loaders, in addition to the drill bit, but not to be immersed in water breaker.
4、不得將破碎器作起吊器具用,不得在挖掘機履帶側操作破碎器。
Breakers shall not be used for lifting equipment shall not operate breaker excavator track side.
5、山東裝載機液壓破碎器工作時的最佳液壓油溫度為50-60度,最高不得超過80度。否則,應減輕液壓破碎器的負載,使用時液壓破碎錘及纖桿應垂直于工作面,以不產生徑向力為原則。
Best hydraulic oil Shandong loaders hydraulic breaker when working temperature is 50-60 degrees, the maximum should not exceed 80 degrees. Otherwise, you should reduce the load on the hydraulic breaker, the use of hydraulic hammers and fiber rods should be perpendicular to the face, so as not to produce radial force principle.
6、被破碎對象已出現破裂或開始產生裂紋時應立即停止破碎器的沖擊,以免出現有害的“空打”。液壓破碎器若要長期停止使用時應放盡氮?dú)?,并將進、出油口密封,切鐵在高溫和-20度以下的環境下存放。
Crushed or broken objects that appear when cracks began to immediately stop the impact breaker to avoid harmful "Runaway." Hydraulic breaker should be used to put a stop to make long-term nitrogen, and into and out of the oil port seal, cut iron at high temperature and -20 degrees below ambient storage.